dc.contributor.author | O'Halloran, Sinéad | |
dc.contributor.author | Harte, Annette M. | |
dc.contributor.author | Shipway, Philip H. | |
dc.contributor.author | Leen, Sean B. | |
dc.date.accessioned | 2019-11-29T09:37:36Z | |
dc.date.available | 2019-11-29T09:37:36Z | |
dc.date.issued | 2017-07-02 | |
dc.identifier.citation | O'Halloran, S. M., Harte, A. M., Shipway, P. H., & Leen, S. B. (2018). An experimental study on the key fretting variables for flexible marine risers. Tribology International, 117, 141-151. doi: https://doi.org/10.1016/j.triboint.2017.07.032 | en_IE |
dc.identifier.issn | 1879-2464 | |
dc.identifier.uri | http://hdl.handle.net/10379/15586 | |
dc.description.abstract | This paper presents an experimental investigation into the effects of contact
conformity, contact pressure and displacement amplitude on the gross-slip fretting behaviour grease-lubricated cylinder-on-flat contacts in the context of flexible marine riser pressure armour wire, and compares behaviour with that observed in unlubricated conditions. Characterisation of friction and wear is critical to fretting fatigue life prediction in flexible risers since friction directly controls trailing-edge fretting stresses and hence fatigue crack initiation, on the one hand, and on the other hand, directly affects wear via relative tangential
slip (displacement). Wear can have a beneficial or detrimental effect on fatigue crack initiation and propagation, depending on relative slip and slip regime. It is shown that friction and wear are higher for dry conditions than for grease-lubricated conditions. For grease-lubricated
conditions, behaviour is determined by whether grease can be retained in the
contact (as opposed to being extruded out). Retention (or replenishment) of grease in the contact results in low rates of wear and low coefficients of friction; these conditions are favoured by fretting displacements above a critical value, by low contact conformity, and by low applied loads. | en_IE |
dc.description.sponsorship | The authors would like to thank the Irish Research Council and Wood Group Kenny for funding of this project through the Enterprise Partnership Scheme (EPSPG/2013/638), the National University of Ireland for funding through a NUI Travelling Scholarship. We also wish to acknowledge the help and support we have received from Dr. Adrian Connaire and Mr. Kieran Kavanagh (Wood Group). The authors also wish to acknowledge the support of the Faculty of Engineering at the University of Nottingham where this research was conducted. | en_IE |
dc.format | application/pdf | en_IE |
dc.language.iso | en | en_IE |
dc.publisher | Elsevier | en_IE |
dc.relation.ispartof | Tribology International | en |
dc.rights | Attribution-NonCommercial-NoDerivs 3.0 Ireland | |
dc.rights.uri | https://creativecommons.org/licenses/by-nc-nd/3.0/ie/ | |
dc.subject | Fretting wear | en_IE |
dc.subject | experimental | en_IE |
dc.subject | grease-lubrication | en_IE |
dc.subject | contact geometry | en_IE |
dc.subject | slip | en_IE |
dc.subject | amplitude | en_IE |
dc.subject | flexible risers | en_IE |
dc.subject | pressure armour layer | en_IE |
dc.subject | nub-groove | en_IE |
dc.title | An experimental study on the key fretting variables for flexible marine risers | en_IE |
dc.type | Article | en_IE |
dc.date.updated | 2019-11-26T16:22:00Z | |
dc.identifier.doi | 10.1016/j.triboint.2017.07.032 | |
dc.local.publishedsource | https://doi.org/10.1016/j.triboint.2017.07.032 | en_IE |
dc.description.peer-reviewed | peer-reviewed | |
dc.contributor.funder | Irish Research Council | en_IE |
dc.contributor.funder | National University of Ireland, Galway | en_IE |
dc.internal.rssid | 15517162 | |
dc.local.contact | Sean Leen, Mechanical & Biomedical Eng, Eng-2051, New Engineering Building, Nui Galway. 5955 Email: sean.leen@nuigalway.ie | |
dc.local.copyrightchecked | Yes | |
dc.local.version | ACCEPTED | |
nui.item.downloads | 221 | |